Metech MAX850 Planetary Grinder
This is a professional machine designed for floor grinding and maintenance. It’s ideal for tasks such as grinding and polishing concrete, stone, and other materials. The machine is suitable for use on various flooring surfaces, including wood floors, terrazzo, marble, granite, and concrete. When paired with specialized grinding consumables, the machine can effectively remove epoxy floor coatings from surfaces.
Analysis of Common Faults of Sparing Machine and Summary of Solutions
1. Smoke from the smoothing machine when working Check the trowel machine to check whether there is too much oil. If there is too much oil, release part of it. It can also be that the piston is broken and severely worn and will burn the oil. If it is damaged, it needs to be replaced in time. Check the engine. If the engine is not faulty, it may also be that there are too many impurities in the oil. The oil is very important. Try to choose high-quality oil. When buying, you must pay attention to prevent buying inferior fake oil. 2. How to level the chassis screws of the smoothing machine First replace 4 new blades and put the trowel in a particularly flat place. Then remove the shift fork and visually inspect whether the heights of the four screws are consistent. If conditions permit, measure them with a ruler. If the heights are inconsistent, adjust them to be consistent. When the gland is gently shaken, if there is no shaking, the debugging is proved successful. Put some butter on the top of the screw to prevent wear. 3. The wiping machine always stalls Observe whether the oil level is normal and whether the oil is too little. Some machines have their own oil protection system, which will automatically turn off when there is a shortage of oil. There is also the fact that after the remote flameout switch and the flameout switch of the machine are disconnected one by one, if the flameout phenomenon does not occur again, it means that there is grounding in that part. Just check and eliminate it carefully. 4. The engine of the trowel is normal, but the trowel is not moved. If there is no problem with the engine, it is caused by the wrong belt type or the belt is too long. If there is still an abnormality, it can be handled by changing a clutch. 5. The gasoline polish machine was blistered First clean the carburetor, let the spark plug be removed to see if there is water in the cylinder head. If there is water, pull the disk several times to drain the water. Try again after changing the oil to see if it is normal. 6. The smoothing machine cannot rotate Reason: The blade may be deformed; the motor bearing is broken; the motor bracket is not fixed well; there is a problem in use.
Method of polishing and grinding
Method of polishing grinding: Grinding is the grinding tool (hereinafter referred to as the grinding tool) surface embedded abrasive or coated abrasive and add lubricant, under certain pressure, the tool and the grinding tool contact and do relative movement, through the abrasive action, from the workpiece surface cut a layer of very thin chip, so that the workpiece has a precise size, accurate geometry and high surface roughness. Its essence is to use free abrasive particles to carry out micro-cutting including physical and chemical comprehensive effects on the surface of the workpiece through the grinding tool. Features:(1) In mechanical grinding, the machine tool-tool-workpiece system is in an elastic floating state. (2) The workpiece to be ground is not subject to any force and is therefore in a free state. (3) The speed of the grinding movement is usually below 30 m/min, which is about 1% of the grinding speed. (4) When grinding, only a very thin layer of material can be cut off, so the heat generated is less, the processing deformation is small, and the surface deterioration layer is also thin. (5) There is residual compressive stress on the grinding surface, which is beneficial to improve the fatigue strength of the workpiece surface. (6) The operation is simple and generally does not require complicated and expensive equipment. (7) Adaptability is good. (8) grinding can obtain very low surface roughness. 1. Fluid polishing Fluid polishing is to rely on high-speed flow of liquid and abrasive particles to wash the surface of the workpiece to achieve the purpose of polishing. Commonly used methods are: abrasive jet processing, liquid jet processing, fluid power grinding. Fluid power grinding is driven by hydraulic pressure, The liquid medium carrying the abrasive particles is caused to flow back and forth at high speed over the surface of the workpiece. The medium mainly uses special compounds with good flowability at lower pressure. (polymer-like substance) and mixed with abrasive, abrasive can be used silicon carbide powder. 2. Mechanical polishing Mechanical polishing is a method of polishing a smooth surface by cutting and plastic deformation of the surface of the material to remove the convex part after polishing, Generally use oilstone, wool wheel, sandpaper, etc., mainly manual operation, special parts such as the surface of the rotary body, Auxiliary tools such as turntables can be used, and the method of super-lapping can be used for high surface quality requirements. Super lapping is a special abrasive tool, In the polishing liquid containing abrasives, it is tightly pressed on the surface of the workpiece to be processed for high-speed rotating motion. Using this technology, the surface roughness of Ra0.008 μm can be achieved, which is the highest among various polishing methods. Optical lens molds often use this method. 3. Ultrasonic polishing The workpiece is placed in the abrasive suspension and placed together in the ultrasonic field, relying on the oscillation of the ultrasonic, The abrasive is ground and polished on the surface of the workpiece. Ultrasonic machining macro force is small, will not cause deformation of the workpiece, but tooling production and installation is difficult. Ultrasonic machining can be combined with chemical or electrochemical methods. On the basis of solution corrosion and electrolysis, ultrasonic vibration is applied to stir the solution, The dissolution products on the surface of the workpiece are separated, and the corrosion or electrolyte near the surface is uniform; Ultrasonic cavitation in the liquid can also inhibit the corrosion process, conducive to surface brightening. 4. Electrolytic polishing The basic principle of electrolytic polishing is the same as chemical polishing, that is, by selectively dissolving the small protruding parts of the surface of the material, Make the surface smooth. Compared with chemical polishing, the effect of cathode reaction can be eliminated, and the effect is better. The electrochemical polishing process is divided into two steps: (1) Macroscopic leveling dissolution products diffuse into the electrolyte, and the geometric roughness of the material surface decreases, Ra> 1μm. (2) micro light level anode polarization, surface brightness, Ra <1μm. 5. Fluid polishing Fluid polishing is to rely on high-speed flow of liquid and abrasive particles to wash the surface of the workpiece to achieve the purpose of polishing. Commonly used methods are: abrasive jet processing, liquid jet processing, fluid power grinding. Fluid power grinding is driven by hydraulic pressure, The liquid medium carrying the abrasive particles is caused to flow back and forth at high speed over the surface of the workpiece. The medium is mainly made of special compounds (polymer-like substances) with good flowability at lower pressure and mixed with abrasives, The abrasive may use silicon carbide powder. 6. Chemical polishing Chemical polishing is to make the surface of the material in the chemical medium micro convex part of the concave part of the preferential dissolution, A smooth surface is thus obtained. The main advantage of this method is that it does not require complex equipment and can polish workpieces with complex shapes, Many workpieces can be polished at the same time with high efficiency. The core problem of chemical polishing is the preparation of polishing solution. Surface roughness obtained by chemical polishing Generally, it is several 10 μm. 7. Magnetic grinding and polishing Magnetic grinding and polishing is the use of magnetic abrasive under the action of a magnetic field to form an abrasive brush to grind the workpiece. This method has high processing efficiency, Good quality, easy control of processing conditions, good working conditions. With suitable abrasives, the surface roughness can reach Ra0.1 μm. The polishing in plastic mold processing is very different from the surface polishing required in other industries, Strictly speaking, the polishing of the mold should be called mirror processing. It not only has the very high request to the polishing itself but also to the surface flatness, There are also high standards for smoothness and geometric accuracy. Surface polishing is generally only required to obtain a bright surface. The standard of mirror processing is divided into four levels: AO = Ra0.008μm, A1 = Ra0.016μm, A3 = Ra0.032μm, A4 = Ra0.063 μm, due to electrolytic polishing, fluid polishing and other methods are difficult to accurately control the geometric accuracy of the part, The surface quality of chemical polishing, ultrasonic polishing, magnetic grinding polishing and other methods can not meet the requirements, so the mirror processing of precision molds Or mainly mechanical polishing.
Take you to understand the characteristics of grinding machine products
Product Features: 1. Imported switch with overload protection has the function of phase loss and leakage protection. 2. Equipped with vacuum cleaner connection device to provide dust-free working environment. 3, fast speed, can work for a long time, high grinding efficiency. 4, can add 12kg of weight iron, can effectively polish the old epoxy floor. 5, can adjust the ground grinding depth. 6. There are four kinds of diamond grinding discs for selection: extra coarse, coarse, medium and fine. The extra coarse disc is especially suitable for removing the old epoxy ground. 7, you can choose the combination of cheap grinding block. 8. The damping device designed with aviation rubber material is flexible and durable.
The situation is as follows: 1. The ground is very uneven, the resistance of the grinding disc is large, and the motor load is too heavy. 2. If this situation occurs when the new machine is used for the first time, it means that the governor has been adjusted to the fastest speed position, or the new grinding plate (block) Not open rough pressure on the rough hard surface, resulting in a large disc resistance, motor load is too heavy. 3. If the gearbox is repaired and the machine is initially tested like this, it may be that the gear assembly is not smooth and too tight, causing the grinding disc to rotate manually. It is not smooth, or the motor shaft and the center gear are not concentric after the motor is fixed during assembly, that is, the rotation is not concentric, which makes the electricity The rotation of the rotor is blocked and Caton occurs. Corresponding solution: 1, the machine up, move to a relatively flat ground area grinding, and then slowly cut into the uneven ground area, or use Other small grinding disc machinery will ground the rough surface of the potholes slightly smooth, and then use the machine to grind. 2. Roughen the grinding piece (block) on the cement floor. Press down on the armrest and raise the starter of the machine (make the grinding disc slightly off the ground). The machine (grinding disc) can be slowly landed. 3. Reassemble the gear or reassemble the motor to make the gear and the grinding disc rotate smoothly. After inserting the motor shaft into the central gear Concentric, suspend the motor and the box and energize the motor to start the motor, so that the motor, gear and grinding disc rotate smoothly. After shutdown, hand Rotate the grinding disc smoothly.
Meitengqi multi-function grinding machine
Meatengqi multifunctional ground grinding machine can be used for grinding concrete ground, with light and flexible operation, grinding and sucking Body, save manpower, grinding and vacuuming into one, while polishing while vacuuming, providing a good dust-free polishing environment. If equipped with sandpaper grinding, can also be polished epoxy putty layer; at the same time on the epoxy putty layer wear small, improve Epoxy floor flatness, with resin drive disc and resin grinding, can be used for liquid hardener construction Sanding and polishing. Use a rubber connector to connect the grinding disc to completely avoid the shock caused by mechanical wear after the equipment has been used for a period of time. movement phenomenon.
MG4P-480 multi-function floor grinding machine
Meitengqi brand MG4P-YY-580 multi-functional floor grinding machine, to meet the needs of professional users for large area industrial floor grinding efficiency, very cost-effective. Suitable for marble, granite, concrete floor grinding renovation, etc. Product Features: 1. The appearance design is novel and elegant. 2. Folding handle, integrated central control panel design, convenient operation, safe and reliable, ergonomic, easy to move the handle. 3, high-power (7.5HP) variable frequency motor, to meet the requirements of industrial floor grinding for a long time and frequent use. 4, automatic pressure adjustment control system, to meet the needs of different construction technology. 5. It can be equipped with dust collection equipment to realize dry and wet working modes. 6. The rotary drain switch and the central water outlet system of the grinding disc can effectively solve the secondary loss of grinding consumables and the grinding line generated during work, thus greatly improving the work efficiency. 7. The multi-functional grinding disc can be installed with various grinding consumables to reduce your construction cost as much as possible. Want to know more welcome to call Guangzhou Qing Qin Yu Environmental Protection Technology Co., Ltd., we wholeheartedly for your service! http://www.qingqinyu.com
How to judge the floor grinding machine gear rotation is good or bad?
In the floor construction, floor grinding machine is very important floor grinding equipment, after long-term use in the process of operation may encounter some faults, which gear rotation is a very important problem, how to judge the floor grinding machine gear rotation is good or bad? 1. Listen to the sound, the floor grinding machine with good processing accuracy can be comparable to the belt drive 2. Look at the selection of materials, high-quality equipment will consider the mechanical heat dissipation performance of mechanical dry grinding, so aluminum alloy material will be selected. 3. Look at the floor grinding machine rotation with the clearance accuracy, with the hand rotation grinding disc test with the clearance. 4. The durability of the floor grinding machine has a great relationship with the design of the box body. After determining the material of the box body, the weight of the mechanical grinding head is determined. If you are interested in the products of the United States, welcome to consult the hotline: 13925069066.
What are the differences between epoxy floor and curing floor performance
The performance comparison of epoxy floor and curing floor is as follows: 1. the mechanical properties of the whole, the mechanical performance of epoxy floor is far less than that of concrete seal curing agent floor, and its wear resistance, pressure resistance and impact resistance are poor. When encountering a high-intensity working environment, it is prone to problems such as peeling and scratching, and the black scratches left by the forklift are difficult to remove. Sealed concrete curing agent in the mechanical properties have a good performance, up to 7-8 Mohs hardness makes it fearless of the vast majority of the impact and rolling, plant common trailers, forklifts can not leave the slightest scratch or tire marks on the curing floor. 2. chemical properties compared to the chemical stability of the epoxy floor is higher, is one of the strongest barrier ability of the floor material, can long time to isolate water, acid, alkali, gasoline, lubricating oil and other substances. Sealed concrete curing agent floor barrier ability is slightly inferior to the epoxy floor, can block the vast majority of water, acid, alkali, oil, juice, dirt, algae and other foreign substances; among them, acidic substances need to be cleaned in time, long time stay easy to leave traces. 3. waterproof and moisture-proof anti-seepage ability epoxy floor thanks to its strong barrier ability, its waterproof and moisture-proof anti-seepage ability is also quite good, is a traditional waterproof floor material; but after scratching, its waterproof will correspondingly plummet. Concrete seal curing agent strictly speaking is not waterproof material, but also has a good waterproof anti-seepage ability, the industry commonly used 24h permeability reduction to express its waterproof ability, through the relevant data we can see its good waterproof ability. 4. aesthetic degree of epoxy floor material used is epoxy resin, is a kind of lacquer material, to create a more shiny floor effect. Concrete seal curing agent floor use to the floor polishing technology, to create the floor has a clear mirror effect, giving a solid texture. 5. safety comparison of environmental protection, concrete seal curing agent belongs to non-toxic harmless water-based inorganic materials, for home decoration is not any problem; epoxy resin itself non-toxic, but the curing material toxic, MDA, TDI, MDI are carcinogenic substances, and will remain in the epoxy resin floor slowly volatilize. In terms of fire protection, the fire protection rating of concrete seal curing agent is the highest A1 level, and the fire protection ability is on the bar. Epoxy resin is not fireproof and will burn under high temperature conditions. Anti-static, epoxy floor in the subdivision of the type-anti-static epoxy resin can achieve the effect of anti-static; concrete seal curing agent floor without the use of epoxy resin secondary construction cases, you can through the construction of anti-static cement mortar to reach the effect of anti-static. 6. the service life of the so-called "into also Xiao he failure also Xiao he", epoxy floor with its strong barrier ability is well-known, but also therefore fold the life, because of poor air permeability, underground rising water vapor easily lead to epoxy floor appear empty drum, rupture and other problems. Generally speaking, the service life of epoxy floor is 2-3 years, and the poor quality may be shortened to 1-2 years, and the depreciation cost is higher. The service life of the concrete seal curing agent floor is up to 20-30 years, which is still a conservative value, in the case of proper maintenance, its service life can even be semi-permanent level, with the same cycle of the building body.
Floor machinery repair and maintenance
Floor machinery is widely used in rough, uneven ground grinding, eradication of concrete floor on the sealing layer and paint and the old epoxy floor innovation, glue and other surface grinding and processing. After a period of operation, if the floor machinery is found to be weak, it can loosen the base screw and adjust the belt adjustment screw. When the operation shows frequent active power failure, please check whether the wire is a national standard 4 square wire, and the wire should be completely opened and cannot be wound together. There is a white connecting wire inside the overload leakage protection switch, and unplug it to see if the connection is firm. If the belt is not loose and the motor rolls, but the site does not rotate, it may be that the pulley is loose. Please open the front cover and reinstall the pulley. If the machine oscillates, please check whether the rubber anti-vibration pad on the site falls off or breaks off. If it falls off, please add a gasket and tighten it. If there is a break, please change it in time. Or there is a corner of the triangular plate under the site that does not have a device. The grinding tool is unbalanced. If oscillation occurs, please replace the grinding tool in time. In the process of use, please fasten the grinding stone with screws to avoid flying out of the site during operation. Please pay attention to safety.
Meitengqi floor grinding machine manufacturers explain the causes of floor bubbles
Floor grinder manufacturers said that floor blisters mostly occur on the first floor or basement, and sometimes above the second floor. Floor blisters are generally found shortly after construction, and some epoxy floors paved in the morning have blisters in the afternoon. Blisters from small to large, continuous development, development to a certain extent after the stop. The higher the temperature, blisters are more likely to occur and develop faster. Blisters vary in shape and size. Some blisters have a diameter of more than 1m and a height of 20~50mm. There is no obvious relationship between the generation of blisters and the construction area. Some of them are serious, some are lighter and some are intact in the same area. The same group operation, the same material construction of the epoxy floor, some blisters, some intact, indicating that blisters are caused by a variety of factors. The cause of blisters is a problem that everyone is concerned about. When the blisters are cut open, it is found that the blisters contain water or yellow liquid. The epoxy ground layer is separated from the base layer, and the cementing material stuck on the base layer is pulled into a peak nest. According to the explanation of "physics", in a closed container containing liquid, the liquid evaporates to form the temperature and pressure relationship of three curves of saturation state. Floor grinding machine manufacturers analysis, which no blisters part of the epoxy layer and the ground part of the bond is not strong, careful observation of the contact part, will also find that there is no curing part, because the epoxy moisture can not cure; so where does the water come from? There are mainly the following sources of water: 1 base, such as cement mortar leveling layer, the maximum water content of about 12%, the maximum water content of the base is greater than the leveling layer. 2. The dehydration of other ingredients in epoxy is endless. 3. Epoxy and base construction when combined with the poor leaving voids and epoxy itself chemical activity, not fully cured or encountered moisture is not fully cured residue or gas. 4. Moist gas permeated underground at the base level.
Why do the factory floor cement curing treatment?
In order to save costs, many factories are put into use directly after the concrete floor is completed without special treatment. But soon, due to various reasons, such as insufficient cement grade, improper maintenance, and repeated rolling by various vehicles, problems will occur on the ground. First, dust and sand, and then potholes will appear, which will not only affect the appearance, but also affect the appearance. Use. At this time, it takes a lot of trouble to find a floor company. Curing the floor is laborious and expensive. Therefore, whether it is a new floor or an old floor, the steel floor should be processed first, including the curing of the floor and the repair of the floor. Sealed concrete curing agent through and concrete material reaction, generate hard material, fill the pores in concrete, improve the strength and wear resistance of concrete floor, so as to thoroughly deal with the problem of cement floor sand. Features: This method has low cost and simple operation, and can solve the problem of dust and sand on the ground. If you want to change the floor surface of cement floor dust and sand, brighten and harden the floor, you can choose concrete curing agent to cooperate with floor grinding machine for floor construction, which can not only effectively prevent the floor from dust and sand, but also increase the hardness of cement floor, and can fully play the role of resistance to wear, wear resistance and pressure resistance. It can be used for a long time, with a service life of more than 20 years and durable, there is a marble-like luster, and the longer the use of gloss, the better.
Analysis and Solution Summary of Common Faults of Smearing Machine
1. Smoke from the smoothing machine when working Check the trowel machine to check whether there is too much oil. If there is too much oil, release part of it. It can also be that the piston is broken and severely worn and will burn the oil. If it is damaged, it needs to be replaced in time. Check the engine. If the engine is not faulty, it may also be that there are too many impurities in the oil. The oil is very important. Try to choose high-quality oil. When buying, you must pay attention to prevent buying inferior fake oil. 2. How to level the chassis screws of the smoothing machine First replace 4 new blades and put the trowel in a particularly flat place. Then remove the shift fork and visually inspect whether the heights of the four screws are consistent. If conditions permit, measure them with a ruler. If the heights are inconsistent, adjust them to be consistent. When the gland is gently shaken, if there is no shaking, the debugging is proved successful. Put some butter on the top of the screw to prevent wear. 3. The wiping machine always stalls Observe whether the oil level is normal and whether the oil is too little. Some machines have their own oil protection system, which will automatically turn off when there is a shortage of oil. There is also the fact that after the remote flameout switch and the flameout switch of the machine are disconnected one by one, if the flameout phenomenon does not occur again, it means that there is grounding in that part. Just check and eliminate it carefully. 4. The engine of the trowel is normal, but the trowel is not moved. If there is no problem with the engine, it is caused by the wrong belt type or the belt is too long. If there is still an abnormality, it can be handled by changing a clutch. 5. The gasoline polish machine was blistered First clean the carburetor, let the spark plug be removed to see if there is water in the cylinder head. If there is water, pull the disk several times to drain the water. Try again after changing the oil to see if it is normal. 6. The smoothing machine cannot rotate Reason: The blade may be deformed; the motor bearing is broken; the motor bracket is not fixed well; there is a problem in use.
Meitengqi milling machine use example
The driving power supply of this machine is three-phase 380V high voltage, so the connection and wiring of power supply and cable is efficient: 1. Flexible operation. Although the weight of the MC320 milling machine reaches 310KG, it can be turned and turned independently by one person under working conditions. 2. A walking speed adjusting mechanism is provided. The suitable walking speed of the milling machine can be adjusted according to the requirements of the milling depth required by the milling machine. 3. It is equipped with a bearing high-temperature butter injection port, and the service life of the bearing can be effectively extended by injecting high-temperature butter regularly and the maintenance cost can be reduced. 4. Equipped with specially designed waterproof, dustproof, high-grade insulation electrical control box, so that the operation safety of construction personnel is guaranteed.
Meidengqi 12T-630 multi-functional floor grinding machine simple operation explanation
1. know 630 Meitengqi 12T-630E multifunctional floor grinding machine series is a professional machine for ground grinding and maintenance. Suitable for concrete, stone grinding, polishing and other work. The machine is suitable for working on wooden floor, terrazzo, marble, granite, concrete and other floors. With special grinding supplies, the machine can be epoxy floor paint surface removal. With 380V three-phase voltage, the speed can reach 1800r. It is suitable for epoxy floor construction of major construction sites, parking stations, warehouses and workshops, and weighs as much as 220kg. In the same type of grinding machine, he is a heavyweight Thanos. At the same time, you can adjust the rotation speed according to your process. The 18kw frequency converter is stable and durable. 2. Operation Indication 1. Step on the multifunctional booster bracket with your left or right foot, and install the protective cover; gently lay the grinder flat; 2. Adjust the operating handle to a suitable position; 3. Add an appropriate amount of water to the water tank; 4. Make sure that the power supply voltage is the same as the machine, check that the machine switch must be in the "off" position, connect the power cord correctly, insert the plug into the body socket, and turn on the power after the red power indicator lights up; 5. Install a grinding disc that matches the nature of the ground, turn on the water switch, put some water in an appropriate amount, and use the rear wheel to tilt the machine off the ground, then start the grinder (note that when starting, the frequency conversion speed control knob switch should slowly adjust the speed, Can be adjusted at will after starting)
In the use of floor grinding machine, some problems should be prevented in a timely manner, if the problem, we need to pay attention to the repair process of which work accurately taking into account the relevant situation, the following floor grinding machine manufacturers to give us a specific introduction. When repairing the floor grinder, only professional workers can disassemble it. Those who are not professional must not disassemble the equipment at will, otherwise it will have a great impact in the process of application. I hope everyone can really consider these specific situations in the process of application and actively consider the specific repair work, after more in place, then the whole repair process will become more frugal. When repairing the floor grinding machine, we should prevent those who do not understand from dealing with it at will. At the same time, we should also find real and professional workers. We should really consider the work in this area and really understand some specific repair methods. This will provide more guarantee for us. Therefore, no matter who is doing it, we should really consider this aspect, then it can bring us more. Unprofessional people cannot disassemble it at will, and at the same time, they should not repair it casually, and they cannot find the problem of the equipment. Sometimes you can repair it twice at will, but there will be some problems in the process of application, and even cause other problems. Therefore, we need to know the location of the problem and communicate with customers in the whole repair process, and tell them where the problem is, and then use the process to prevent similar work from happening. Learn to accurately do a good job in all aspects of understanding, for the whole repair process has more attention, in the future in the process of using will become more assured. Repair will directly affect the future use, so we need to treat it steadily.
Meidengqi MG4P-480 multifunctional floor grinding machine
Meitengqi MG4P-480 multifunctional floor grinding machine to meet the needs of professional users for large area industrial floor grinding efficiency, very cost-effective. Suitable for marble, granite, concrete floor grinding renovation, etc. Product Features: 1. The appearance design is novel and elegant. 2. Folding handle, integrated central control panel design, convenient operation, safe and reliable, ergonomic, easy to move the handle. 3, high-power (7.5HP) variable frequency motor, to meet the requirements of industrial floor grinding for a long time and frequent use. 4, automatic pressure adjustment control system, to meet the needs of different construction technology. 5. It can be equipped with dust collection equipment to realize dry and wet working modes. 6. The rotary drain switch and the central water outlet system of the grinding disc can effectively solve the secondary loss of grinding consumables and the grinding line generated during work, thus greatly improving the work efficiency. 7. The multi-functional grinding disc can be installed with various grinding consumables to reduce your construction cost as much as possible.
During floor construction, the floor grinding machine shall clean up the replaced grinding pieces after each grinding, so as not to cause irreparable scratches on the ground due to gravel in the grinding pieces during the next construction, especially during curing treatment. When the ground is repaired, remember to clean up the grinding pieces. As a dust-free construction technology specially used for curing floor construction, when the ground is repaired, if the repair agent and repair mortar are sprinkled for "grinding method" repair, the grinding piece is stained with repair agent and repair mortar or repair material, which needs to be cleaned up in time, otherwise it is not easy to get after drying. And if you don't pay attention to, floor grinding machine with these pieces of grinding on the ground, it will cause damage to the ground, may not be able to repair, may also spend a lot of time to repair, add trouble to the floor construction. So in the floor grinding machine after curing repair, especially grinding repair, to remember to check the cleaning of metal grinding. The Meitengqi grinding machine produced by Guangzhou Qing Qin Yu Environmental Protection Technology Co., Ltd. gives you the products you want and are applicable. Welcome to consult Contact: Ms. Wu Tel: 86 020 38989152 Mobile Phone: 13925069066 Fax: 86 020 38989166
Room 1010, South Tower, XinDacheng Plaza, 27 Erheng Road, Shuiyin Road, Yuexiu District, Guangzhou, China