NEWS

News

Contact Us

Guangzhou Qing Qin Yu Environmental Protection Technology Co., Ltd.


Sales Center: Room 1010, South Tower, Xindacheng Plaza, 27 Erheng Road, Shuiyin Road, Yuexiu District, Guangzhou



Fax: 020-38989166





There are several methods of floor pretreatment? What are the characteristics of each?

Release time:

2023-11-10 16:51

Floor processing equipment manufacturer Guangzhou Qing Qin Yu Environmental Protection Technology Co., Ltd. tells you: There are several methods of floor pretreatment? What are the characteristics of each?
 
Floor pretreatment includes grinding, milling and sandblasting. Grinding is a soft concrete floor to be treated so that the coating can have good contact with the ground. Milling and planing is used to carry out pre-destruction treatment on the ground with higher strength to enhance the adhesion of the coating. Sandblasting is used in places with higher requirements. This method can achieve the best adhesion between the coating and the ground (for example, some ground has been precipitated by oil stains for many years, need to do epoxy floor, such as steel plate and other high strength of the base)
 
recommend ground grinder: Meitengqi W301 two-in-one ground grinder
 
Product Features:
 
1: automatic balance, can be used for different ground grinding.
 
2: grinding diversification, can choose according to the floor grinding.
 
3: The first domestic use of high-speed dust-free grinding machine.
 
4: Imported bearings, high wear resistance, prolong service life.
 
5: intelligent adjustment speed, troubleshooting can increase the use of the effect and convenience.
 
6: can be installed grinding PCD cutter head diamond grinding plate, metal grinding plate, resin grinding plate, refurb, water grinding plate, sand leather
 
 
 
For more information on the floor, please visit the official website "Baidu Input [Meitengqi]" of Guangzhou Qing Qin Yu Environmental Protection Technology Co., http://www.qingqinyu.com

Related News

Under the background of high-quality development, how will the road and bridge industry develop?

In the first year of the 14th Five-Year Plan, China's economy has entered a stage of high-quality development, transforming the mode of economic development, optimizing the economic structure, transforming the driving force of economic growth, and realizing the structural transformation from medium and low-end industries to medium and high-end industries is the theme of economic development for a long time in the future. With the gradual decline of the marginal utility of investment in economic pull, and the proposal of the new development pattern of "double cycle", China's economic growth drive is gradually changing from investment-driven to consumption-driven, therefore, the future investment growth rate of the construction industry will inevitably slow down further. As an important part of the construction industry, the road and bridge engineering construction industry plays a very important role in maintaining the normal operation of social production, circulation, distribution, and consumption, ensuring the sustained, rapid and healthy development of the national economy, improving people's living standards, and promoting the modernization of national defense. However, with the continuous improvement of the highway network and national and provincial highways, the market space of the road and bridge industry is under pressure, and the competition is becoming increasingly fierce. In the future, there are five main trends in the development of the road and bridge industry: First, industrial chain extension and related diversification are effective ways to deal with growth bottlenecks. The upstream and downstream expansion of the industrial chain includes the mining and manufacturing of upstream raw materials, downstream real estate, operation, and EPC construction general contracting. The related diversified development mainly extends to rail transit, water conservancy, environmental protection, maintenance engineering and other fields. Second, the concentration of the industry continues to increase, and market competition is further intensified. The market concentration of the construction industry is low and there are many players. However, with the further deepening of the marketization of the industry and the deterioration of the international environment, large and medium-sized enterprises such as central enterprises and provincial state-owned enterprises have begun to enter the city to seize the regional market and hinder the industry from breaking through. The influencing factors of geographical restrictions have been continuously weakened, the cross-regional competition of the industry has become increasingly significant, and the market concentration is expected to continue to increase. Third, the growth of the eastern market space is limited, and the western market has more room for development. With the low density of road network in the western region and the promotion of relevant policy factors such as the large-scale development of the western region and "Belt and Road Initiative", the investment in infrastructure construction in the western region is gradually strengthening and has become a key area for domestic highway construction. Fourth, intelligent transportation has become a new bright spot in the field of highway construction. Driven by technologies such as ultra-high-speed wireless local area network and 5G mobile communication, smart transportation will be greatly developed in the future. Fifth, the qualification reform promotes the road and bridge enterprises to enhance the degree of marketization and comprehensive strength. In March 2020, the Measures for the Administration of Engineering Cost Consulting Enterprises and the Measures for the Administration of Registered Cost Engineers proposed to lower the qualification threshold for cost enterprises. In July 2020, the Ministry of Housing and Construction issued the Framework of Qualification Standards for Construction Engineering Enterprises (Draft for Comments), proposing to significantly reduce the qualification categories and grades of enterprises. Lowering the entry threshold for the construction industry will further promote road and bridge enterprises to change the traditional concept of "waiting and relying on, really improve the construction ability, technical strength and management ability.


2023-10-17

Analysis and Solution Summary of Common Faults of Smearing Machine

1. Smoke from the smoothing machine when working Check the trowel machine to check whether there is too much oil. If there is too much oil, release part of it. It can also be that the piston is broken and severely worn and will burn the oil. If it is damaged, it needs to be replaced in time. Check the engine. If the engine is not faulty, it may also be that there are too many impurities in the oil. The oil is very important. Try to choose high-quality oil. When buying, you must pay attention to prevent buying inferior fake oil. 2. How to level the chassis screws of the smoothing machine First replace 4 new blades and put the trowel in a particularly flat place. Then remove the shift fork and visually inspect whether the heights of the four screws are consistent. If conditions permit, measure them with a ruler. If the heights are inconsistent, adjust them to be consistent. When the gland is gently shaken, if there is no shaking, the debugging is proved successful. Put some butter on the top of the screw to prevent wear. 3. The wiping machine always stalls Observe whether the oil level is normal and whether the oil is too little. Some machines have their own oil protection system, which will automatically turn off when there is a shortage of oil. There is also the fact that after the remote flameout switch and the flameout switch of the machine are disconnected one by one, if the flameout phenomenon does not occur again, it means that there is grounding in that part. Just check and eliminate it carefully. 4. The engine of the trowel is normal, but the trowel is not moved. If there is no problem with the engine, it is caused by the wrong belt type or the belt is too long. If there is still an abnormality, it can be handled by changing a clutch. 5. The gasoline polish machine was blistered First clean the carburetor, let the spark plug be removed to see if there is water in the cylinder head. If there is water, pull the disk several times to drain the water. Try again after changing the oil to see if it is normal. 6. The smoothing machine cannot rotate Reason: The blade may be deformed; the motor bearing is broken; the motor bracket is not fixed well; there is a problem in use.


2023-10-16

Method of polishing and grinding

Method of polishing grinding: Grinding is the grinding tool (hereinafter referred to as the grinding tool) surface embedded abrasive or coated abrasive and add lubricant, under certain pressure, the tool and the grinding tool contact and do relative movement, through the abrasive action, from the workpiece surface cut a layer of very thin chip, so that the workpiece has a precise size, accurate geometry and high surface roughness. Its essence is to use free abrasive particles to carry out micro-cutting including physical and chemical comprehensive effects on the surface of the workpiece through the grinding tool. Features:(1) In mechanical grinding, the machine tool-tool-workpiece system is in an elastic floating state. (2) The workpiece to be ground is not subject to any force and is therefore in a free state. (3) The speed of the grinding movement is usually below 30 m/min, which is about 1% of the grinding speed. (4) When grinding, only a very thin layer of material can be cut off, so the heat generated is less, the processing deformation is small, and the surface deterioration layer is also thin. (5) There is residual compressive stress on the grinding surface, which is beneficial to improve the fatigue strength of the workpiece surface. (6) The operation is simple and generally does not require complicated and expensive equipment. (7) Adaptability is good. (8) grinding can obtain very low surface roughness. 1. Fluid polishing Fluid polishing is to rely on high-speed flow of liquid and abrasive particles to wash the surface of the workpiece to achieve the purpose of polishing. Commonly used methods are: abrasive jet processing, liquid jet processing, fluid power grinding. Fluid power grinding is driven by hydraulic pressure, The liquid medium carrying the abrasive particles is caused to flow back and forth at high speed over the surface of the workpiece. The medium mainly uses special compounds with good flowability at lower pressure. (polymer-like substance) and mixed with abrasive, abrasive can be used silicon carbide powder. 2. Mechanical polishing Mechanical polishing is a method of polishing a smooth surface by cutting and plastic deformation of the surface of the material to remove the convex part after polishing, Generally use oilstone, wool wheel, sandpaper, etc., mainly manual operation, special parts such as the surface of the rotary body, Auxiliary tools such as turntables can be used, and the method of super-lapping can be used for high surface quality requirements. Super lapping is a special abrasive tool, In the polishing liquid containing abrasives, it is tightly pressed on the surface of the workpiece to be processed for high-speed rotating motion. Using this technology, the surface roughness of Ra0.008 μm can be achieved, which is the highest among various polishing methods. Optical lens molds often use this method. 3. Ultrasonic polishing The workpiece is placed in the abrasive suspension and placed together in the ultrasonic field, relying on the oscillation of the ultrasonic, The abrasive is ground and polished on the surface of the workpiece. Ultrasonic machining macro force is small, will not cause deformation of the workpiece, but tooling production and installation is difficult. Ultrasonic machining can be combined with chemical or electrochemical methods. On the basis of solution corrosion and electrolysis, ultrasonic vibration is applied to stir the solution, The dissolution products on the surface of the workpiece are separated, and the corrosion or electrolyte near the surface is uniform; Ultrasonic cavitation in the liquid can also inhibit the corrosion process, conducive to surface brightening. 4. Electrolytic polishing The basic principle of electrolytic polishing is the same as chemical polishing, that is, by selectively dissolving the small protruding parts of the surface of the material, Make the surface smooth. Compared with chemical polishing, the effect of cathode reaction can be eliminated, and the effect is better. The electrochemical polishing process is divided into two steps: (1) Macroscopic leveling dissolution products diffuse into the electrolyte, and the geometric roughness of the material surface decreases, Ra> 1μm. (2) micro light level anode polarization, surface brightness, Ra <1μm. 5. Fluid polishing Fluid polishing is to rely on high-speed flow of liquid and abrasive particles to wash the surface of the workpiece to achieve the purpose of polishing. Commonly used methods are: abrasive jet processing, liquid jet processing, fluid power grinding. Fluid power grinding is driven by hydraulic pressure, The liquid medium carrying the abrasive particles is caused to flow back and forth at high speed over the surface of the workpiece. The medium is mainly made of special compounds (polymer-like substances) with good flowability at lower pressure and mixed with abrasives, The abrasive may use silicon carbide powder. 6. Chemical polishing Chemical polishing is to make the surface of the material in the chemical medium micro convex part of the concave part of the preferential dissolution, A smooth surface is thus obtained. The main advantage of this method is that it does not require complex equipment and can polish workpieces with complex shapes, Many workpieces can be polished at the same time with high efficiency. The core problem of chemical polishing is the preparation of polishing solution. Surface roughness obtained by chemical polishing Generally, it is several 10 μm. 7. Magnetic grinding and polishing Magnetic grinding and polishing is the use of magnetic abrasive under the action of a magnetic field to form an abrasive brush to grind the workpiece. This method has high processing efficiency, Good quality, easy control of processing conditions, good working conditions. With suitable abrasives, the surface roughness can reach Ra0.1 μm. The polishing in plastic mold processing is very different from the surface polishing required in other industries, Strictly speaking, the polishing of the mold should be called mirror processing. It not only has the very high request to the polishing itself but also to the surface flatness, There are also high standards for smoothness and geometric accuracy. Surface polishing is generally only required to obtain a bright surface. The standard of mirror processing is divided into four levels: AO = Ra0.008μm, A1 = Ra0.016μm, A3 = Ra0.032μm, A4 = Ra0.063 μm, due to electrolytic polishing, fluid polishing and other methods are difficult to accurately control the geometric accuracy of the part, The surface quality of chemical polishing, ultrasonic polishing, magnetic grinding polishing and other methods can not meet the requirements, so the mirror processing of precision molds Or mainly mechanical polishing.


2023-10-12

What does the floor grinder floor grinder inverter display oL2 mean? Why can't the machine start? How to solve?

The situation is as follows: 1. The ground is very uneven, the resistance of the grinding disc is large, and the motor load is too heavy. 2. If this situation occurs when the new machine is used for the first time, it means that the governor has been adjusted to the fastest speed position, or the new grinding plate (block) Not open rough pressure on the rough hard surface, resulting in a large disc resistance, motor load is too heavy. 3. If the gearbox is repaired and the machine is initially tested like this, it may be that the gear assembly is not smooth and too tight, causing the grinding disc to rotate manually. It is not smooth, or the motor shaft and the center gear are not concentric after the motor is fixed during assembly, that is, the rotation is not concentric, which makes the electricity The rotation of the rotor is blocked and Caton occurs. Corresponding solution: 1, the machine up, move to a relatively flat ground area grinding, and then slowly cut into the uneven ground area, or use Other small grinding disc machinery will ground the rough surface of the potholes slightly smooth, and then use the machine to grind. 2. Roughen the grinding piece (block) on the cement floor. Press down on the armrest and raise the starter of the machine (make the grinding disc slightly off the ground). The machine (grinding disc) can be slowly landed. 3. Reassemble the gear or reassemble the motor to make the gear and the grinding disc rotate smoothly. After inserting the motor shaft into the central gear Concentric, suspend the motor and the box and energize the motor to start the motor, so that the motor, gear and grinding disc rotate smoothly. After shutdown, hand Rotate the grinding disc smoothly.


2023-10-09